baluap


Bearing
Mei 3, 2009, 4:44 am
Filed under: Mechanical Engineer

A bearing is a device to allow constrained relative motion between two or more parts, typically rotation or linear movement. Bearings may be classified broadly according to the motions they allow and according to their principle of operation as well as by the directions of applied loads they can handle.

Bearing friction

Low friction bearings are often important for efficiency, to reduce wear and to facilitate high speeds. Essentially, a bearing can reduce friction by virtue of its shape, by its material, or by introducing and containing a fluid between surfaces.

By shape, gains advantage usually by using spheres or rollers.
By material, exploits the nature of the bearing material used. (An example would be using plastics that have low surface friction.)
By fluid, exploits the low viscosity of a layer of fluid, such as a lubricant or as a pressurized medium to keep the two solid parts from touching.
By fields, exploits electromagnetic fields, such as magnetic fields, to keep solid parts from touching.

Combinations of these can even be employed within the same bearing. An example of this is where the cage is made of plastic, and it separates the rollers/balls, which reduce friction by their shape and finish.

Principles of operation

There are at least six common principles of operation:

sliding bearings, usually called “bushes”, “bushings”, “journal bearings”, “sleeve bearings”, “rifle bearings”, or “plain bearings”
olling-element bearings such as ball bearings and roller bearings
jewel bearings, in which the load is carried by rolling the axle slightly off-center
fluid bearings, in which the load is carried by a gas or liquid
magnetic bearings, in which the load is carried by a magnetic field
flexure bearings, in which the motion is supported by a load element which bends.

Motions

Common motions permitted by bearings are:

Axial rotation e.g. shaft rotation
Linear motion e.g. drawer
spherical rotation e.g. ball and socket joint
hinge motion e.g. door

Loads

Bearings vary greatly over the size and directions of forces that they can support.

Forces can be predominately radial, axial (thrust bearings) or moments perpendicular to the main axis.

Speeds

Different bearing types have different operating speed limits. Speed is typically specified as maximum relative surface speeds, often specified ft/s or m/s. Rotational bearings typically describe performance in terms of the product DN where D is the diameter (often in mm) of the bearing and N is the rotation rate in revolutions per minute.

Generally there is considerable speed range overlap between bearing types. Plain bearings typically handle only lower speeds, rolling element bearings are faster, followed by fluid bearings and finally magnetic bearings which are limited ultimately by centripetal force overcoming material strength.

Play and elasticity

Some applications apply bearing loads from varying directions and accept only limited play or “slop” as the applied load changes. One source of motion is gaps or “play” in the bearing. As example, a 10 mm shaft in a 12 mm hole has 2 mm play. A second source of motion is elasticity in the bearing itself. As example, the balls in a ball bearing are like stiff rubber, and under load deform from round to a slightly flattened shape. The race is also elastic and develops a slight dent where the ball presses on it.

Allowable play varies greatly depending on the use. As example, a wheelbarrow wheel supports radial and axial loads. Axial loads may be hundreds of newtons force left or right, and it is typically acceptable for the wheel to wobble by as much as 10 mm under the varying load. In contrast, a lathe may position a cutting tool to ±0.02 mm using a ball lead screw held by rotating bearings. The bearings support axial loads of thousands of newtons in either direction, and must hold the ball lead screw to ±0.002 mm across that range of loads.

Life

Fluid and magnetic bearings can potentially give indefinite life.

Rolling element bearing life is statistical, but is determined by load, temperature, maintenance, vibration, lubrication and other factors.

For plain bearings some materials give much longer life than others. Some of the John Harrison clocks still operate after hundreds of years because of the lignum vitae wood employed in their construction, whereas his metal clocks are seldom run due to potential wear.

Maintenance

Many bearings require periodic maintenance to prevent premature failure, although some such as fluid or magnetic bearings may require little maintenance.

Most bearings in high cycle operations need periodic lubrication and cleaning, and may require adjustment to minimise the effects of wear.

History and development

An early type of linear bearing uses tree trunks laid down under sleds. This technology may date as far back as the construction of the Pyramids of Giza, though there is no definitive evidence. Modern linear bearings use a similar principle, sometimes with balls in place of rollers.

The first plain and rolling-element bearings were wood, but ceramic, sapphire, or glass were also used, and steel, bronze, other metals, ceramics, and plastic (e.g., nylon, polyoxymethylene, teflon, and UHMWPE) are all common today. A “jeweled” pocket watch uses stones to reduce friction, and allow more precise time keeping. Even old materials can have good durability. As examples, wood bearings can still be seen today in old water mills where the water provides cooling and lubrication.

Rotary bearings are required for many applications, from heavy-duty use in vehicle axles and machine shafts, to precision clock parts. The simplest rotary bearing is the sleeve bearing, which is just a cylinder inserted between the wheel and its axle. This was followed by the roller bearing, in which the sleeve is replaced by a number of cylindrical rollers. Each roller behaves as an individual wheel. The first practical caged-roller bearing was invented in the mid-1740s by horologist John Harrison for his H3 marine timekeeper. This uses the bearing for a very limited oscillating motion but Harrison also used a similar bearing in a truly rotary application in a contemporaneous regulator clock.

An early example of a wooden ball bearing (see rolling-element bearing), supporting a rotating table, was retrieved from the remains of the Roman Nemi ships in Lake Nemi, Italy. The wrecks were dated to 40 AD. Leonardo da Vinci is said to have described a type of ball bearing around the year 1500. An issue with ball bearings is the balls rub against each other, causing additional friction, but rubbing can be prevented by enclosing the balls in a cage. The captured, or caged, ball bearing was originally described by Galileo in the 1600s. The mounting of bearings into a set was not accomplished for many years after that. The first patent for a ball race was by Philip Vaughan of Carmarthen in 1794.

Friedrich Fischer’s idea from the year 1883 for milling and grinding balls of equal size and exact roundness by means of a suitable production machine formed the foundation for creation of an independent bearing industry.

A patent, reportedly the first, was awarded to Jules Suriray, a Parisian bicycle mechanic, on 3 August 1869.[1] The bearings were then fitted to the winning bicycle ridden by James Moore in the world’s first bicycle road race, Paris-Rouen, in November 1869.[2]

The modern, self-aligning design of ball bearing is attributed to Sven Wingquist of the SKF ball-bearing manufacturer in 1907.

Henry Timken, a 19th century visionary and innovator in carriage manufacturing, patented the tapered roller bearing, in 1898. The following year, he formed a company to produce his innovation. Through a century, the company grew to make bearings of all types, specialty steel and an array of related products and services.

Erich Franke invented and patented the wire race bearing in 1934. His focus was on a bearing design with a cross section as small as possible and which could be integrated into the enclosing design. After World War II he founded together with Gerhard Heydrich the company Franke & Heydrich KG (today Franke GmbH) to push the development and production of wire race bearings.

The Timken Company (Sale $4,973.4M, 2006), The SKF company ($6,195.1M, 2005), the Schaeffler Group (Private), the NSK company ($5,344.5M, 2006), and the NTN Bearing company ($3,697.8M, 2006) are now the largest bearing manufacturers in the world.

Today, bearings are used in a variety of applications. Ultra high speed bearings are used in dental hand pieces, aerospace bearings are used in the Mars Rover, and flexure bearings are used in optical alignment systems.

Iklan

Tinggalkan sebuah Komentar so far
Tinggalkan komentar



Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s



%d blogger menyukai ini: